★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions
Free Instant Download NEW 352-001 Exam Dumps (PDF & VCE):
Available on:
https://www.certleader.com/352-001-dumps.html
Cause all that matters here is passing the Cisco 352-001 exam. Cause all that you need is a high score of 352-001 CCDE Written Exam exam. The only one thing you need to do is downloading Testking 352-001 exam study guides now. We will not let you down with our money-back guarantee.
2021 Oct b-gl-352-001:
Q21. When a design calls for spanning VLANs across a campus network, what are two issues that need to be addressed in the design? (Choose two.)
A. network convergence
B. network accessibility
C. fault isolation
D. application scalability
E. user experience
Answer: AC
Q22. A company plans to establish a new network using Cisco Catalyst switches for its multicast applications. What is the disadvantage when two multicast applications are using the multicast IP addresses 234.17.4.5 and 234.145.4.5 inside the same network?
A. Multicast packets from both applications are flooded to all Layer 2 ports in a segment where a multicast receiver is located.
B. Multicast packets from both applications are flooded to ports where one multicast receiver from one application is located.
C. Only one multicast stream is received at the port where the receivers from both applications are located.
D. Both multicast senders will always receive the multicast packets from the other multicast application.
E. The routers doing PIM-SM cannot distinguish between the two multicast applications.
Answer: B
Q23. After the recent implementation of a new design that incorporated GRE tunnels into the network, the network operations staff is seeing the following syslog message in multiple routers on the network - %TUN-5-RECURDOWN: Tunnel0 temporarily disabled due to recursive routing.
From a design perspective, what was not taken into account prior to implementing the solution?
A. The neighboring routers cannot respond within the specified hold time.
B. The interface on the router that is the source of the tunnel is down.
C. The interface on the neighboring router that is the source of the tunnel is down.
D. The router is learning the route to the tunnel destination address using the tunnel interface.
E. The tunnel interface on the router is not receiving any keepalives within the specified hold time.
Answer: D
Q24. Refer to the exhibit.
In the DWDM network, a ring topology carries multiple services between two sites. Which option describes the employed protection design?
A. Y-cable protection
B. Splitter protection
C. Client protection
D. UDLD
E. FEC protection
Answer: C
Q25. You have created a network design that has two point-to-point Metro Ethernet circuits extending a single production VLAN between two data centers. Under normal circumstances, one circuit will carry traffic and spanning tree will block the other. If the company wants you to make use of both circuits to carry production traffic, which two technologies and features will you investigate to integrate into your network design? (Choose two.)
A. EtherChannel
B. MST
C. Multichassis EtherChannel
D. PVST+
Answer: AC
Abreast of the times 352-001 actual test:
Q26. In a large enterprise network with multiple data centers and thousands of access devices, OSPF is becoming unstable due to link flapping. The current design has the access devices multihomed to large aggregation routers at each of the data centers. How would you redesign the network to improve stability?
A. Add a layer of regional Layer 3 aggregation devices, but leave the ABR function on the data center aggregation routers.
B. Add a layer of regional Layer 2 aggregation devices, but leave the ABR function on the data center aggregation routers.
C. Add a layer of regional Layer 3 aggregation devices and move the ABR function to the regional aggregation device.
D. Add a layer of regional Layer 2 aggregation devices and move the ABR function to the regional aggregation device.
Answer: C
Q27. You are evaluating convergence characteristics of various interior gateway protocols for a new network design. Which technology allows link-state routing protocols to calculate paths to destination prefixes that are functionally similar to feasible successors in Enhanced Interior Gateway Routing Protocol?
A. Incremental Shortest Path First
B. Cisco Multiprotocol Label Switching Traffic Engineering Fast Reroute
C. Loop-Free Alternate Fast Reroute
D. partial route calculation
E. Fast-Flooding
Answer: C
Q28. Currently a service provider provides IPv4 traceroute services between MPLS PE routers. The provider wants to implement IPv6 with MPLS 6PE/6VPE and then provide parallel IPv6 traceroute services between MPLS PE routers. Which two design solutions provide this service? (Choose two.)
A. The P routers must support ICMPv6.
B. The PE routers must support ICMPv6.
C. The P routers must support full IPv6.
D. The PE routers must support full IPv6.
Answer: BD
Q29. A switched network is being designed to support a manufacturing factory. Due to cost constraints, fiber-based connectivity is not an option. Which design allows for a stable network when there is a risk of interference from the manufacturing hardware in use on the factory floor?
A. Design the network to include UDLD to detect unidirectional links and take them out of service.
B. Design the network to include EtherChannel bundles to prevent a single-link failure from taking down a switch interconnection point.
C. Design the network to include loop guard to prevent a loop in the switched network when a link has too much interference.
D. Design the network to include BackboneFast on all devices to accelerate failure convergence times.
Answer: A
Q30. You are designing a large-scale DMVPN network with more than 500 spokes using EIGRP as the IGP protocol. Which design option eliminates potential tunnel down events on the spoke routers due to the holding time expiration?
A. Increase the hold queue on the tunnel interface of the spoke routers.
B. Increase the hold queue on the physical interface of the spoke routers.
C. Increase the hold queue on the physical interface of the hub router.
D. Increase the hold queue on the tunnel interface of the hub router.
E. Apply QoS for pak_priority class.
Answer: D