★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions
Free Instant Download NEW 200-125 Exam Dumps (PDF & VCE):
Available on:
https://www.certleader.com/200-125-dumps.html
Examination 200-125, name as CCNA Cisco Certified Network Associate CCNA (v3.0). 200-125 examination is really a impressive certification today that is definitely demanded by way of several The idea industry experts for obtaining higher status and high level of experience of their relevant area of interest. Documentation for Examination 200-125 gives evident opportunities of having good task and career. By permitting Cisco 200-125 certification you can lift up your well worth and value in front of your current organisations.
2021 Mar 200-125 sample question
Q11. - (Topic 7)
What are three values that must be the same within a sequence of packets for Netflow to consider them a network flow? (Choose three.)
A. source IP address
B. source MAC address
C. egress interface
D. ingress interface
E. destination IP address
F. IP next-hop
Answer: A,D,E
Explanation:
Each packet that is forwarded within a router or switch is examined for a set of IP packet attributes. These attributes are the IP packet identity or fingerprint of the packet and determine if the packet is unique or similar to other packets.
Traditionally, an IP Flow is based on a set of 5 and up to 7 IP packet attributes. IP Packet attributes used by NetFlow:
• IP source address
• IP destination address
• Source port
• Destination port
• Layer 3 protocol type
• Class of Service
• Router or switch interface
All packets with the same source/destination IP address, source/destination ports, protocol interface and class of service are grouped into a flow and then packets and bytes are tallied. This methodology of fingerprinting or determining a flow is scalable because a large amount of network information is condensed into a database of NetFlow information called the NetFlow cache.
Reference: http://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/ios- netflow/prod_white_paper0900aecd80406232.html
Q12. - (Topic 8)
Refer to the exhibit.
What is the result of setting the no login command?
A. Telnet access is denied.
B. Telnet access requires a new password at the first login.
C. Telnet access requires a new password.
D. no password is required for telnet access.
Answer: D
Q13. - (Topic 4)
Which two statistics appear in show frame-relay map output? (Choose two.)
A. the number of BECN packets that are received by the router
B. the value of the local DLCI
C. the number of FECN packets that are received by the router
D. the status of the PVC that is configured on the router
E. the IP address of the local router
Answer: B,D
Explanation:
Sample “show frame-relay map” output: R1#sh frame map
Serial0/0 (up): ip 10.4.4.1 dlci 401(0x191,0x6410), dynamic, broadcast,, status defined, active
Serial0/0 (up): ip 10.4.4.3 dlci 403(0x193,0x6430), dynamic, broadcast,, status defined, active
Serial0/0 (up): ip 10.4.4.4 dlci 401(0x191,0x6410), static, CISCO, status defined, active
Q14. - (Topic 8)
Which two security appliances will you use in a network? (Choose two.)
A. ATM
B. IDS
C. IOS
D. IOX
E. IPS
F. SDM
Answer: B,E
Q15. - (Topic 8)
Which address class includes network 191.168.0.1/27?
A. Class C
B. Class B
C. Class D
D. Class A
Answer: B
Abreast of the times 200-125 sample question:
Q16. - (Topic 4)
What occurs on a Frame Relay network when the CIR is exceeded?
A. All TCP traffic is marked discard eligible.
B. All UDP traffic is marked discard eligible and a BECN is sent.
C. All TCP traffic is marked discard eligible and a BECN is sent.
D. All traffic exceeding the CIR is marked discard eligible.
Answer: D
Explanation:
Committed information rate (CIR): The minimum guaranteed data transfer rate agreed to by the Frame Relay switch. Frames that are sent in excess of the CIR are marked as discard eligible (DE) which means they can be dropped if the congestion occurs within the Frame Relay network.
Note: In the Frame Relay frame format, there is a bit called Discard eligible (DE) bit that is used to identify frames that are first to be dropped when the CIR is exceeded.
Q17. - (Topic 5)
Which command enables IPv6 forwarding on a Cisco router?
A. ipv6 local
B. ipv6 host
C. ipv6 unicast-routing
D. ipv6 neighbor
Answer: C
Explanation:
To enable IPv6 routing on the Cisco router use the following command: ipv6 unicast-routing
If this command is not recognized, your version of IOS does not support IPv6.
Q18. - (Topic 3)
Refer to the exhibit.
According to the routing table, where will the router send a packet destined for 10.1.5.65?
A. 10.1.1.2
B. 10.1.2.2
C. 10.1.3.3
D. 10.1.4.4
Answer: C
Explanation:
The destination IP address 10.1.5.65 belongs to 10.1.5.64/28, 10.1.5.64/29 & 10.1.5.64/27 subnets but the “longest prefix match” algorithm will choose the most specific subnet mask
-> the prefix “/29 will be chosen to route the packet. Therefore the next-hop should be
10.1.3.3 ->.
Q19. - (Topic 5)
Which three statements about Syslog utilization are true? (Choose three.)
A. Utilizing Syslog improves network performance.
B. The Syslog server automatically notifies the network administrator of network problems.
C. A Syslog server provides the storage space necessary to store log files without using router disk space.
D. There are more Syslog messages available within Cisco IOS than there are comparable SNMP trap messages.
E. Enabling Syslog on a router automatically enables NTP for accurate time stamping.
F. A Syslog server helps in aggregation of logs and alerts.
Answer: C,D,F
Explanation:
The Syslog sender sends a small (less than 1KB) text message to the Syslog receiver. The Syslog receiver is commonly called "syslogd," "Syslog daemon," or "Syslog server." Syslog messages can be sent via UDP (port 514) and/or TCP (typically, port 5000). While there are some exceptions, such as SSL wrappers, this data is typically sent in clear text over the network. A Syslog server provides the storage space necessary to store log files without using router disk space.
In general, there are significantly more Syslog messages available within IOS as compared to SNMP Trap messages. For example, a Cisco Catalyst 6500 switch running Cisco IOS Software Release 12.2(18)SXF contains about 90 SNMP trap notification messages, but has more than 6000 Syslog event messages.
System logging is a method of collecting messages from devices to a server running a syslog daemon. Logging to a central syslog server helps in aggregation of logs and alerts. Cisco devices can send their log messages to a UNIX-style syslog service. A syslog service accepts messages and stores them in files, or prints them according to a simple configuration file.
Reference: http://www.cisco.com/c/en/us/products/collateral/services/high-availability/white_paper_c11-557812.html
Q20. - (Topic 5)
Which option is a valid IPv6 address?
A. 2001:0000:130F::099a::12a
B. 2002:7654:A1AD:61:81AF:CCC1
C. FEC0:ABCD:WXYZ:0067::2A4
D. 2004:1:25A4:886F::1
Answer: D
Explanation:
An IPv6 address is represented as eight groups of four hexadecimal digits, each group representing 16 bits (two octets). The groups are separated by colons (:). An example of an IPv6 address is 2001:0db8:85a3:0000:0000:8a2e:0370:7334. The leading 0’s in a group can be collapsed using ::, but this can only be done once in an IP address.