★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions

Free Instant Download NEW 350-001 Exam Dumps (PDF & VCE):
Available on: https://www.certleader.com/350-001-dumps.html


We have each of the necessary Cisco 350-001 practice questions and also answers which are closely equal to the Cisco 350-001 actual exam. The particular Cisco Cisco exam dumps are compiled and verified by way of multiple times. Every one of the Cisco 350-001 exam syllabuses are incorporated in our 350-001 items. The variety of Cisco practice questions will be the same as the real Cisco 350-001 exam, thats multiple choice which makes you as if on the actual test day.

2021 Sep cisco ccie 350 001:

Q141. You use OSPF as your network routing protocol. You use the command show ip route and you see several routes described as 0, 0 IA, 0 E1, and 0 E2. What routes are in your area?

A. OIA

B. OE1

C. O E2

D. 0

Answer: D


Q142. Which switch port error is an indication of duplex mismatches on 10/100/1000 IEEE 802.3u Gigabit Ethernet ports?

A. FCS errors

B. Runts

C. Multiple collisions

D. Alignment errors

Answer: C


Q143. Refer to the exhibit.


By default, why will BGP choose a locally originated route over any iBGP or eBGP learned route?

A. The IGP metric to the next hop is always shorter.

B. Locally originated routes have a better AD than eBGP or iBGP routes.

C. All locally originated routes have a better origin code.

D. Locally originated routes have a higher metric.

E. Locally originated routes have a weight of 32, 768.

Answer: E


Q144. There is some confusion on this sim and what it is. So I will tell you that it is a window with 4 squares on the left side. Click each one to see the question. Again, there are 4 questions and one topology. Click the `topology' button at the bottom of the sim to see it. There is only one topology for all 4 questions. You do NOT log into any routers. All configuration is provided as text in the question.

NOTE: The actual topology may vary with the routing protocol questions selected for the sim and the number of routers could be as high as R6


Given R1#show ipv6 mroute

(*, FF02::2), 00:02:57/never, RP 2002:2222::2, flags: SPC Incoming interface: FastEthernet0/0

RPF nbr: FE80::266:66FF:FE66:6666

(*, FF04::6), 00:02:57/never, RP 2002:2222::2, flags: SPC Incoming interface: FastEthernet0/0

RPF nbr: FE80::266:66FF:FE66:6666

A. Some thing about expiry for Multicast group 1 after 60 second

B. The Multicast group address is 2002:2222::2

C. Some thing about expiry for Multicast group 1 after x second

D. The RP address is 2002:2222::2

E. The Multicast Group addresses are FF02::2 and FF04::6

F. The Multicast Group addresses are (FF08:: some strange number i think it was the RPF NBR)

G. The operating Mode is sparse mode

Answer: DEG


Q145. Refer to the exhibit.


Which two statements are correct, when the QoS configuration is applied in an outbound direction on a 10-Mb/s interface? (Choose two.)

A. When reaching 10 Mb/s of input rate, the video class will be policed to 200 kb/s.

B. The class FTP is allowed to reach more than 1 Mb/s in the event of congestion.

C. IP precedence 1 traffic is affected by a drop probability.

D. Video traffic above 200 kb/s is allowed to pass when the total interface output rate does not reach 10 Mb/s.

E. Video traffic above 200 kb/s is allowed to pass when congestion is present.

Answer: BD


350-001 exam answers

Renewal cisco 350 001:

Q146. In order to configure two routers as anycast RPs, which of these requirements, af a minimum, must be satisfied?

A. Multicast Source Discovery Protocol mesh-groups must be configured between the two anycast RPs.

B. The RPs must be within the same IGP domain.

C. Multicast Source Discovery Protocol must be configured between the two anycast RPs.

D. The two anycast RPs must be IBGP peers.

Answer: C


Q147. Refer to the exhibit. In this network, R1 has been configured to advertise a summary route, 192.168.0.0/22, to R2. R2 has been configured to advertise a summary route, 192.168.0.0/21, to R1. Both routers have been configured to remove the discard route (the route to null created when a summary route is configured) by setting the administrative distance of the discard route to 255. What will happen if R1 receives a packet destined to 192.168.3.1?


A. The packet will loop between R1 and R2.

B. It is not possible to set the administrative distance on a summary to 255.

C. The packet will be forwarded to R2, where it will be routed to null0.

D. The packet will be dropped by R1, since there is no route to 192.168.3.1.

Answer: A


Q148. Router 1 is configured for BGP as dual-homed on the Cisco network. Which three BGP attributes are carried in every BGP update on this router (both IBGP and EBGP)? (Choose three.)

A. origin

B. router-ID

C. AS-path

D. local-preference

E. next-hop

Answer: ACE


Q149. You are a network technician, study the exhibit carefully. In this EIGRP network, the output of the command show interface for the link between R2 and R5 indicates that the link load varies between 10 and 35. Which K value setting will be used to make sure that this link is not used by EIGRP when the link load reaches 35, but can be used again when the link load drops below 20?


A. Link load is not read in real time, so there is no way to set the K values to make EIGRP choose to use or not use a link based on the link load.

B. There is not enough information in the to determine the correct answer.

C. Use the K5 setting to include load in EIGRP's metric calculations.

D. Use the K2 setting to include load in EIGRP's metric calculations.

Answer: A


Q150. Refer to the exhibit.


R4 is unable to establish an EIGRP adjacency with R3, the only other router on the Fa0/0 LAN segment, although it is able to ping R3. An EIGRP debug on R4 does not provide any clues. What might be the cause of the problem?

A. The passive interface has disabled the transmission of EIGRP multicast hello packets.

B. EIGRP on R4 should be routing to network 209.165.202.128/28.

C. The designated router/backup designated router (DR/BDR) selection requires that at least three routers are on a LAN.

D. The routing metrics on R4 and R3 are different.

Answer: A